#acl merlyn:read,write All:read
<<TableOfContents()>>
== HP MSA 2040 ==
=== Setting network port IP addresse s using the CLI port and cable ===
{{{
  * Preparing a Linux computer be fore cabling to the CLI port
Although Linux operating systems do not require installation  of a device driver, certain parameters must be provided 
during driver loading to enable recognition of the MSA 2040 controller enclosures. 
To load the Linux device driver with the correct parameters, the following command is required:

modprobe usbserial vendor=0x210c product=0xa4a7 use_acm
}}}
{{{
Network ports on controller module A 
and controller module B are configured with the following factory-default IP 
settings:
•
Management Port IP Address
:
10.0.0.2 (controller A), 10.0.0.3 (controller B)
•IP Subnet Mask
: 255.255.255.0
•
Gateway IP Address
: 10.0.0.1


Press Enter
 to display the CLI prompt (#).
The CLI displays the system versio
n, MC version, and login prompt:
a.
At the login prompt, enter the default user
manage.
b.
Enter the default password
!manage.
}}}

=== set advanced-settings  missing-lun-response notready|illegal ===
  * illegal: Sends a reply that there is a LUN but that the request is “illegal.” Sense data returned 
is sensekey = 5, code = 25h, qualifier = 0. If the system is used in a VMware environment, use this option.



== Hardware Information finding - How in HP-UX Server ==
You can find the serial number and All Hardware info from the MP console for Low, Middle and High End servers :
    --> MP:CM> DF -NC - ALL

On integrity Servers : # machinfo

== HPE Hard Disk Drives - Hard Drive Model Number Matrix ==
  * HP ProLiant Gen8/Gen9 Servers - How to Get Memory, Power Supply, Smart Storage Battery and Hard Drive Part Information from iLO 4

http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=mmr_kc-0123838

http://h20566.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c00305257

== Reset ILO password ==
https://blog.netnerds.net/2006/04/ribcl-reset-administrator-password-on-ilo/

Using hponcfg you do not need a valid username/password, but the syntax needs to be in the XML file your feeding to iLO

= Troubleshooting =
== Fault code : 3061 (hard) ==
 * http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c01502707&sp4ts.oid=316040
 * http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c01566716
 * http://community.hpe.com/t5/Tape-Libraries-and-Drives/MSL5026-Bin-fetch-failure-3011/td-p/3629418
{{{
HP recommend this for the error:
â ¢ Press the Enter button to reboot.
â ¢ Ensure cartridges are fully inserted in the magazine(s).
â ¢ Ensure that there are no obstructions inside the library (all cartridges are in magazines).
â ¢ Run the cartridge cycle diagnostic to verify.
â ¢ Check the tape cartridge used in the last operation for damage. 
}}}

= How to upgrade the firmware of the HP Onboard Administrator =
https://jreypo.wordpress.com/tag/hp-onboard-administrator/

== Reboot Onboard Administrator and Firmware Upgrade "online" ==
http://community.hpe.com/t5/HPE-BladeSystem/Reboot-Onboard-Administrator-and-Firmware-Upgrade-quot-online/td-p/5994903

=  Reboot or reset iLO hung session of HP Blade Server using CLI =
http://www.serverhead.com/reset-ilo-hung-hp-blade-server-oa-cli-ssh-telnet/

https://rhoadesbrown.wordpress.com/2011/08/04/managing-ilos-from-an-onboard-administrator-c-class-enclosure/